![]() Not only do you need to ensure that it will install into your wall easily but you must also make sure it can support your TV safely. Well, because that mount will support your expensive television. However, with wall mounts, this becomes doubly important. Of course, you should check the build quality of every product you buy to ensure it’s high-quality. Not too expensive because you don’t want to pay an exorbitant amount of money for a wall mount and not too cheap because you want a high-quality product. The key is to find the right balance between not too expensive and not too cheap. Hence, it’ll end up costing you more in the long run. In this case, you’ll have to spend more money to replace the mount. While it may seem like you’ve saved a lot of money at first, there’s a high chance that the mount may break down within a few weeks or months. That’s because if you spend too little and buy an extremely cheap wall mount, then you can end up with a mount that’s poorly designed and made from sub-par materials. In addition to not spending too much money, you must also be careful about not spending too little. Hence, you don’t need to spend more than that unless you’re buying a mount that’s custom-made for your television.Įven full-motion mounts, which are the most expensive types of mounts, are available for less than $100 both online and in electronics stores. This is because we have found that you can find extremely high-quality wall mounts for less than $100 easily in the market. In most cases, we recommend that you don’t spend more than $100. It’s good to have an idea of how much money you’re willing to spend on a TV mount. ![]() Naturally, you need to consider the price of the TV mount you intend to buy. Fortunately, you can look towards some common factors to determine which mount could be best for your needs. If you’re buying a TV mount for the first time and you’ve been browsing online for one, chances are that you may be even more confused than ever.ĭon’t worry as that’s a common feeling among consumers that are in the market for a TV mount. In my experience, Its measurements range from 200 x 100 mm to 600 x 400 mm. You can move it up and down, turn it side to side, and pull it out of the wall.Ĭompatibility: The mount is VESA compatible. Mount type: In our testing, It’s a full-motion mount, and like all other mounts of this type, it gives you all the moving options you’d expect. While it will cost you a lot of money, we believe the price is well worth it. Price: This mount is not exactly the cheapest but that’s because it’s a full-motion mount made from high-quality Steel. It should not be difficult to install because it comes with all of the necessary mounting hardware and clear and concise instructions.įactors to Consider Before you Decide to Buy Mounting Dream MD2296-24 Full-Motion TV Mount Not only is it exceptionally durable, but setting it up is also a piece of cake. You won’t have to worry about the stability of your television set when it’s connected to this mount. They should also be snug.This full-motion mount’s superior steel construction makes it ideal for single-stud wall mounts and other heavy displays. Since you will only have 3/4" of engagement, use lots of extra screws. The screws from the TV mount into the plywood need to engage into the plywood, all else is wasted. You want the plywood to be somewhat in compression against the drywall, the drywall's best strength (and tension is the screw's best strength). Worst case if the threads engage the plywood, it can end up causing the plywood to push away and then stand off from the wall, putting the screw entirely in shear, not its best strength. You don't want the threads engaging to the plywood, but rather, the stud. It would also help to drill the plywood out to the major diameter (edge of thread) of the lag bolts. For best results, pre-drill a hole into the stud somewhat smaller than the minor diameter (all-solid diameter) of the lag bolt. The lag bolts through the plywood into the studs need to be long enough to go through the plywood, through the drywall, and engage about 1-1/4" to 1-1/2" into the stud proper - not any further or you risk hitting electrical gear.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |